Dimmers
Products
GRMS » Wired GRMS Range » Dimmers »
DALI/DMX Controller for 64 Ballasts
Product Number: DALI-DMX-64
- The unit EMDC-64M is designed to control DALI electronic ballasts and DMX receivers from the DynamicPro system.
- EMDC-64M enables control of up to 64 independent electronic ballasts
- DALI (Digital Addressable Lighting Interface) for fluorescent lamps, LEDs and other light sources.
- EMDC-64M also enables connection of up to 64 DMX receivers (Digital MultipleX).
- Control from DynamicPro BUS System via EBM BUS.
- DIP switches on the front panel to select the control interface (DALI/DMX).
- Addressing of DALI ballast units can be done via the central unit and iDM3 software or via MINI USB on the front panel of the EMDC-64M and DALI Configurator software.
- The required functionality is set in user project in iDM3 software.
- The unit EMDC-64M is powered from the mains voltage 230 V AC.
- DALI BUS power supply is 16 V/250 mA via an EMDC-64M unit.
- The system BUS EBM is galvanically separated from the BUSes DALI/DMX. Terminals for connecting the DALI BUS are equipped with short circuit and surge protection.
- It is possible to connect up to 8 EMDC-64M units to one EBM BUS.
- If this concerns the last unit on a system BUS EBM, it is necessary to terminate the wire with a resistor with nominal resistance of 120 Ω. The resistor is inside the unit, termination is made by shorting neighboring terminals TERM and EBM+.
- The BUS DMX must be terminated at its end by a resistor with nominal resistive value 120 Ω. The resistor for DMX BUS termination is on the side of the EMDC- 64M inside the unit, termination is performed by shorting adjacent terminals TERM and A.
- Updating the firmware of the EMDC-64M can be done through the central unit adn software iDM3 or via MINI USB on the front panel and EMDC-64M Flasher software. Updating through MINI USB must be done while system BUS EBM is disconnected.
- When configuring DALI addresses two types are necessary to distinguished:
- MASTER – this group includes sensors and detectors and one DALI branch can connect up to 4 DALI MASTER units - lighting intensity sensor DLS3-1
- motion detector DMD3-1
– SLAVE – electronic lighting ballast - EMDC-64M in 3-MODULE design is designed for mounting in a control panel on a DIN rail EN60715.
Order Inquiry
Description
- The unit EMDC-64M is designed to control DALI electronic ballasts and DMX receivers from the DynamicPro system.
- EMDC-64M enables control of up to 64 independent electronic ballasts
- DALI (Digital Addressable Lighting Interface) for fluorescent lamps, LEDs and other light sources.
- EMDC-64M also enables connection of up to 64 DMX receivers (Digital MultipleX).
- Control from DynamicPro BUS System via EBM BUS.
- DIP switches on the front panel to select the control interface (DALI/DMX).
- Addressing of DALI ballast units can be done via the central unit and iDM3 software or via MINI USB on the front panel of the EMDC-64M and DALI Configurator software.
- The required functionality is set in user project in iDM3 software.
- The unit EMDC-64M is powered from the mains voltage 230 V AC.
- DALI BUS power supply is 16 V/250 mA via an EMDC-64M unit.
- The system BUS EBM is galvanically separated from the BUSes DALI/DMX. Terminals for connecting the DALI BUS are equipped with short circuit and surge protection.
- It is possible to connect up to 8 EMDC-64M units to one EBM BUS.
- If this concerns the last unit on a system BUS EBM, it is necessary to terminate the wire with a resistor with nominal resistance of 120 Ω. The resistor is inside the unit, termination is made by shorting neighboring terminals TERM and EBM+.
- The BUS DMX must be terminated at its end by a resistor with nominal resistive value 120 Ω. The resistor for DMX BUS termination is on the side of the EMDC- 64M inside the unit, termination is performed by shorting adjacent terminals TERM and A.
- Updating the firmware of the EMDC-64M can be done through the central unit adn software iDM3 or via MINI USB on the front panel and EMDC-64M Flasher software. Updating through MINI USB must be done while system BUS EBM is disconnected.
- When configuring DALI addresses two types are necessary to distinguished:
- MASTER – this group includes sensors and detectors and one DALI branch can connect up to 4 DALI MASTER units - lighting intensity sensor DLS3-1
- motion detector DMD3-1
– SLAVE – electronic lighting ballast - EMDC-64M in 3-MODULE design is designed for mounting in a control panel on a DIN rail EN60715.
Specification
- DynamicPro BUS/EBM: EBM
- DALI/DMX BUS: 64 channels / 64 channels
- Supply voltage: AC 230 V (50/60 Hz), max. 100 mA
- Housing: 3-MODULE
- Dimensions: 90 x 52 x 65 mm
Downloads
Contact Us
- Address:
CANADA: Unit 157 – 99 Scurfield Boulevard, Winnipeg, MB, R3Y 1Y1 , CANADA.
UAE: LIU No.11 Dubai Silicon Oasis P.O. Box 293640 Dubai United Arab Emirates - Email us:
info@dynamicpro.ca
info@ateis.ae - Call:
Canada Office: +1 (204) 306 5173
UAE Office: +971 (4) 3262730
